Deadlines reference snapshot for New York

Rule or statute summary

Run this scenario in DocketMath using the Deadline calculator.

This New York “deadline snapshot” captures the general default statute of limitations (SOL) rule most people look for when they’re trying to determine a basic outside deadline. In other words: if you don’t have a claim-type-specific SOL rule identified, you may start with the general rule below.

General/default SOL for New York (5 years)

• Default SOL period: 5 years
• Where it comes from: **N.Y. Crim. Proc. Law § 30.10(2)(c)
• Scope you should assume: This is treated here as the general SOL period you use when you have not identified a more specific, claim-type-specific deadline rule.

How DocketMath fits in

Use DocketMath to turn the general/default rule into a working date:

• Open the calculator here: /tools/deadline
• DocketMath’s deadline calculator is designed for the practical workflow of:

  • entering a relevant start date (the trigger date that begins the limitations period), and
  • using the SOL length shown in this snapshot (5 years).
• The calculator outputs an estimated “last day”—the typical outside deadline under the selected inputs.

Because SOL rules can turn on the “trigger date” (for example, occurrence date vs. discovery date, and other legal triggers), the same SOL length can still produce different end dates depending on your chosen input.

Gentle disclaimer: This is a reference snapshot, not legal advice. For any time-sensitive matter, it’s wise to confirm the applicable trigger and whether a different claim-type-specific SOL rule controls.

Citations

Use these sources to confirm the authoritative text before finalizing the calculation.

• N.Y. CPLR § 5513

When rules change, rerun the calculation with updated inputs and store the revision in the matter record.

If an assumption is uncertain, document it alongside the calculation so the result can be re-run later.

Default SOL period (5 years)

• Statute: **N.Y. Crim. Proc. Law § 30.10(2)(c)
• Source link: https://www.nysenate.gov/legislation/laws/CPL/30.10
• General/default period stated in this snapshot: 5 years

What this page does not do

• Claim-type-specific sub-rules: No claim-type-specific sub-rule was identified for this snapshot beyond the general/default period above. That means this page does not map the 5-year rule to particular cause-of-action categories.

Use the calculator

You can use DocketMath to compute a concrete deadline from the 5-year default rule.

Run the Deadline calculation in DocketMath, then save the output so it can be audited later: Open the calculator.

Capture the source for each input so another team member can verify the same result quickly.

Inputs to consider

SOL deadlines depend heavily on which date starts the clock, so before you calculate, confirm your trigger/start date.

Common input patterns include:

• Start date: the date the relevant event occurred (or the date your limitations clock begins under the rule you believe applies)
• SOL length: for this snapshot, use 5 years

If your facts suggest a different trigger (for example, a statute that starts counting from a discovery date rather than an occurrence date), you should update the calculator inputs accordingly—otherwise the computed end date may not reflect the governing rule.

Output: how to interpret it

After you enter your start date, DocketMath will compute:

• Estimated deadline date: an estimated last day the limitations period would expire under the 5-year rule.

If later you determine that your matter uses a different SOL length or a different trigger date, rerun the calculator with corrected inputs to update the output.

Quick decision checklist (practical)

Before relying on the computed output, check:

Timing note: SOL calculations can be sensitive to exact timing. A one-day difference in the start date can shift the estimated end date by nearly a full day.

Example workflow (illustrative)

1. Choose your start date (the date you believe begins the SOL clock).
2. In DocketMath, set/use the 5-year default rule.
3. Review the computed “deadline date.”
4. If you confirm a different SOL rule or trigger applies, update inputs and rerun.

Related reading

• Why deadlines results differ in Canada — Troubleshooting when results differ
• Deadlines reference snapshot for New Hampshire — Rule summary with authoritative citations
• Emergency deadline checklist for Canada — Emergency checklist and quick-reference inputs